We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.
If you’re wondering how to install baseboard inside corner, you’re not alone. If you’ve never done it before, you may be confused and worried about the process. Here are a few tips to make it easier:
Measure for 90-degree corner
Ensure a tight fit with a miter saw when installing baseboard by measuring for a 90-degree corner before cutting the trim. To make sure that you’re cutting for a tight fit, round the length up a few inches, and then add an extra inch or two to the overall length. If possible, install baseboard with two outside miters; if not, hire a carpenter or contractor to complete the job.
The inside corner is three degrees off the finish floor, and the right side is nine degrees off. Hold the left-side of the baseboard up against the fence, and measure the angle from there. The bevel angle is 22.5 degrees to the left. Remember to avoid rounded corners, which have a slow turn and cannot be cut straight. Use a protractor to accurately measure for a 90-degree corner.
For mitered corners, you should measure from the corner to the first obstruction, such as a door molding or another corner of the room. A corner may be inside or outside a 90-degree angle, depending on the size of the room. The longest measurement is the point where the walls meet and form a corner, and the end of the trim will touch it afterward. In this way, you’ll be able to create a clean-looking edge.
You should also make sure you measure for corners when installing baseboard. Corners may be difficult to get perfectly mitered corners, because walls rarely are square. Cutting two pieces of adjacent trim at 45-degree angles is also not an ideal way to achieve a perfect miter corner. Consequently, the spaces between the pieces of trim may look uneven, making them look amateurish. A carpenters bevel square or protractor is an invaluable tool for measuring corners.
Mark opposite ends of baseboard for straight cuts
The easiest way to mark the opposite ends of baseboard for straight cuts when you’re installing inside corners is to place it in the location where you want to install it. Then, mark the length with a tape measure. When cutting baseboards, set your miter saw at 90 degrees and make a straight cut where you plan to fit against any obstructions. Position the cut baseboard into place, checking that the miter joint fits tightly together without a gap.
Make a rough measurement for the length of the baseboard to ensure that the cut is accurate. Mark opposite ends so the carpenter knows where to cut. If you’re installing inside corners, use a miter saw instead of a coping saw. Set the saw at 0 degrees to cut a square angle. Even though you’re making a straight cut, you’re unlikely to get it right the first time.
If you don’t want to use a jigsaw, you can use a table saw instead. It’s much easier to use a table saw than a jigsaw. You’ll need a steady bench, and a flat surface to ensure you’re cutting the baseboard straight. Also, you’ll need a sharp saw to cut around doorways, as they often have molding around them. Using a miter saw, you can butt the baseboard against the molding, and you can even use the same technique if the doorway has curved walls.
Make sure to measure and mark the opposite ends of baseboard for the angles you want. It’s much easier to make precise measurements with a sharp utility knife than with a pencil. For 45-1/2-degree angles, use a utility knife. Make sure to measure an extra 1/8 inch in front of the baseboard to account for a miter that has a straight back and open front.
Nail baseboard to baseboard
When you nail a baseboard to an inside corner, make sure to make a 45-degree cut at the end of the board. This small piece will cap the end of the wall. You should use wood glue to secure the piece to the wall, as brad nails may break. Then, use a nail gun with a compressor or a cordless nailer. You should follow the manufacturer’s instructions when installing corner blocks.
To properly nail a baseboard to a wall, you must follow the proper method for cutting the corner. The correct method will depend on the type of corner or bend in the wall. Make sure to sketch the layout of your room before you begin. This will help you determine which corners to cut. Use the correct nails for each corner. Then, nail the baseboard to the wall. Use a finishing nail to complete the process.
Before nailing a baseboard to the wall, it is a good idea to use wax paper. If you can’t find wax paper in the corner, you can try using a short piece of masking tape. This will help you to cut the baseboard properly. It may be necessary to scrape away the wax paper or make a straight cut before nailing it to the wall. If you’re not confident with your cutting skills, you can hire a professional.
When you want to install a baseboard, it’s important to make sure you nail the baseboard into the studs. If you’re not sure about this, use a stud finder. The device beeps when it finds a stud, so use it. You should then use a pencil to mark the studs. This will help you prioritize the nailing process.
Sand and prime baseboards
Before you can sand and paint your baseboards, they must be clean. You can clean them with hot water and a rag to remove any excess wood filler. If the baseboards are particularly grimy, use TSP in the water to clean them. Then, sand them with a 150-grit sandpaper to create a smooth finish and a slightly eased edge. This step will ensure that the baseboards hold the paint better and last longer.
Once you have completed the sanding process, you can start putting the baseboards in place. To do this, first measure the length of the wall and the inside corner. Add about an inch to each measurement. If the wall isn’t level, use a stud finder or knock on the wall to determine where the studs are. When installing your baseboards, make sure to nail two nails into each stud. You can use a nail gun or nail set to use an appropriate angle for this. Once the nails are in place, fill any hole that is left behind with putty. If the corner isn’t perfectly straight, apply wood glue on the mitered edges. Unless you’re installing the baseboards inside a corner, you’ll probably want to use wood glue instead.
If you’re painting your baseboards, you’ll need to use a wood primer. The wood filler will look unsightly if it isn’t properly primed. A quality wood primer will hide the gaps and help the paint adhere better. Also, if the baseboards are installed on an angle, the inside corner will develop gaps between the walls. Sanding and priming them will prevent these gaps from developing.
Use outside corner blocks
To install baseboard inside the corners of the walls, place a block in the corner. Drill holes one inch inside the corner block from the top left to the bottom right. Use a nail set to secure the block to the wall. Next, cut the baseboard to fit flush against the blocks. Then, secure it to the walls with nail sets. Caulk the top and bottom edges and vertical seams.
Corner blocks are most commonly used for masonry constructions. They come in L or triangular shapes and fit over the inside corner of the molding. You can use a nail gun or tap to secure the block to the wall. Wood glue works well to fill the holes made by the block. Use outside corner blocks when installing baseboards inside the corners. These blocks also add accent to the trim work. Use one of these blocks for every corner of the room.
Before you install the baseboard inside the corner, you should trim the blocks. The blocks should be 3/4 inches taller than the baseboard. For the best results, use blocks that are at least half an inch taller than the baseboard. Then, reinstall the baseboard and finish. If you need to adjust the height of the corner block, you can use blocks of varying length. You may also need to repaint the corner blocks on occasion.
When you are done installing the baseboard, you should fasten it to the wall using screws or nails. Before installing the baseboard, you should also prepare the walls and prime or paint them. You should also carve away any hidden drywall to achieve a tight fit. You can also dry fit it by drilling a few holes in it and making sure the edges are flat. Then, sand the corner blocks and prime it before painting it.
