Woodworking

How to Sharpen a Wood Chisel? Comprehensive Guide

If your chisel isn’t sharp, don’t expect to do any good work with it. Most tools are ready to use once their manufacturing process is complete. however, chisels don’t fall under that category. 

After manufacture, chisels tend to be ground to a bevel of between 25 to 35 degrees. However, you need to put the final edge on it before it’s ready.

So, this guide is here to help you do just that. Note that there are alternative sharpening methods with more complex tools, such as grinding wheels in the mix. However, this series of steps focus on a bit of a simpler alternative with more easily accessible components.

Still, this is not the most barebones method you could use. Some people sharpen their chisels exclusively by hand. You can think of this as a midpoint.

Gather Your Materials and Tools

Before getting started, it’s important to gather everything you’re going to need for the task. Having a chisel goes without saying, but there are three more elements that are required for this methodology to work period

The first is your honing guide, which maintains the blade angle as you sharpen. Of course, if you have a ton of experience, then you can get the angle by feel. However, if you did have that much experience, you probably wouldn’t be reading this guide.

Sharpening stones are necessary as well, and they’re probably going to represent the costliest component of the operation. Two combination stones (800/4,000 and 1,200/8,000) should do the trick.

With a water stone grit of 6,000 or greater, a nagura stone is needed to create the slurry that helps with chisel sharpening.

Water Stones

The first thing you want to do is have your water stones sit in some water. That one was probably kind of obvious. You don’t need to have them submerged for ages as some people may think.

In less than 20 minutes, they should be good to go. The jury is still out on if storing these stones in water is a good idea or not. Just in case you may not have realized, your nagura stone should also be submerged here.

Honing Guide

Now, you set up your honing guide by putting the chisel into it with the bevel face down. You want to tighten the guide just enough to hold the chisel, but you don’t want it too tight. When you’re done, you should be able to adjust the chisel.

You don’t have to worry about pinpoint accuracy, as you just need the bevel to lay flush against the stone. Once you’ve achieved your desired level of adjustment, you need only tighten your honing guide screw, which should then lock the chisel in place.

Sharpening Stones

Water stones can be slippery, so remember to put them somewhere that prevents them from sliding around unnecessarily. 

With your chisel in the honing guide, you want to set the whole arrangement onto the stone, with even pressure on the chisel blade’s back. Here, you want to give it five to six passes forward and back. At this point, you are using your 800-grit stone.

For maximum usability, don’t have all your passes go over the same area of the stone. Distribute things as evenly as possible. If you start developing grooves in your stones, you have a problem.

Every three passes, wipe your blade clean, check your progress, rinse any residue that accumulated on the stone, and go again. 

Related Post

The next step is to move to your 1,200-grit stone, repeat the process above, then move to the 4,000-grit stone. It’s at this point that you’re going to notice your blade beginning to shine.

Nagura Stone

While the larger water stone grits are fine on their own, when you get to 6,000 and above, these finer water stones need some help to produce the slurry that is essential in sharpening the chisel effectively.

That was the whole purpose of your getting a nagura stone. Now that you’ve passed the 4,000-grit level, only the 8,000-grit sharpening procedure remains.

If you’ve been following along so far, your nagura stone should be wet at this point. Take the 8,000-grit stone and rub atop it in a circular motion. With that, you’re going to notice this slurry starting to form atop the stone.

Once done, you can take your chisel/honing guide assembly and repeat the same process you did above. The only difference is that after rinsing the 8,000-grit stone each time, you want to do a nagura stone reapplication. 

You’re approaching the finish line here, so just press on for a couple more steps!

Second Bevel

The second bevel is sometimes called a micro-bevel. While it’s not mandatory, you can save yourself a lot of time in the future by having one. 

Why would you want to do this? Well, your chisel is inevitably going to get dull over time, which requires subsequent sharpening. All you would need to do is sharpen your micro-bevel, and you’re good to go.

Of course, at some point, your micro-bevel does flatten and align with the rest of the bevel. but it takes quite some time, meaning that you are not going to have to do this whole process every time.

Start by creating the slurry on your 8,000-grit stone with your nagura stone. With your chisel and honing guide assembly on the stone, you want to raise the chisel’s handle a bit. Push forward from one side of the stone to the next with a smooth and steady stroke.

You don’t want to pull the blade backward on the stone after each pass. Instead, lift the chisel and bring it back to the nearer side. Each time you do this, raise the chisel handle in small, fixed increments by the same angle.

When done, the end of your chisel blade should feature a thin line.

Back Flattening

While you’ve done well so far, you’ve also created a burr on the back of the blade’s edge. Get your 800-grit stone and lie the back of the chisel against it. Make several passes, ensuring that the chisel is completely flat against the stone.

You only need to flatten the end here, but keeping more of the chisel along the stone helps you to keep things flat. Repeat the process moving to the 1,200-grit and then the 4,000-grit stone.

Final Remarks

Now you know what it takes to flatten a chisel. Remember that there are other methods you can use, but this one is fairly simple, and the tools are easy to acquire.

Itamar Ben Dor

My father is a practical engineer, and as a hobby he was also involved in construction, renovations, carpentry and woodwork at home; So there was always tools, saws, drills and more at home. Already I was a little kid Dad and I would renovate the house. Once we built a shed for garden tools, once we did flooring for the garden, once we renovated the bathroom and that’s the way it is. Long before there was an internet, directories and plans. We would build things, kitchen cabinets, install electrical appliances, do flooring, pour concrete and more ... I in this blog want to pass on to you the experience I have gained over the last 20 plus-minus years since I was a child to this day and give you information about the best tools, project plans, guides and more.

Recent Posts

Closing Balconies

Closing balconies can be done in a variety of ways. The options include a sliding…

4 months ago

Choosing a Wheelchair

Whether you are looking for a Powerchair, Beach wheelchair, or a Manual Wheelchair, there are…

5 months ago

What You Need to Know About Solar Panels

Solar panels are devices that convert sunlight into electricity. They are typically made of silicon…

5 months ago

Types of Synthetic Grass Recommended For Purchase

While the price of synthetic grass may seem high, there are many advantages to having…

7 months ago

Poplar vs Pine: Which is better for your project?

Wood is a natural material that has been used by humans for construction and other…

8 months ago

How to Choose the Right Router for Your Needs

Anyone involved in woodworking knows that a router is an essential tool. But with so…

8 months ago