We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.
If you’re interested in learning how to replace a bathtub faucet, there are a few things you should know first. Before beginning the task, be sure to disconnect the water supply lines and remove the escutcheon plate and handle. Once you have removed these, you’ll need to unscrew the spout’s set screw. Turn the spout to loosen it, but be careful not to wiggle the spout. This could cause problems with the plumbing.
Disconnect supply lines before installing new faucet
Before you can install a new bathtub faucet, you must disconnect the existing supply lines. These lines run behind the tub faucet and connect the supply water. To disconnect them, you must unscrew the swivel nuts from the faucet body. If the tub has a shower riser, you will need to unscrew the showerhead pipe, as well. Then, you can replace the bathtub faucet assembly, following the instructions that come with the new faucet assembly.
After disconnecting the supply lines, remove the old faucet and replace it. To do this, you need a basin wrench. Be careful not to damage the water lines, as they may be in the way of the retaining nut. Wrap them in protective material, if you don’t want to damage them. Leaving them exposed can result in leakage and other problems. Once you’ve completed all of these steps, you’re ready to install a new bathtub faucet.
When replacing a bathtub faucet, remember to disconnect the supply lines before beginning the project. Before you begin, you’ll need to make sure the plumbing is in good condition and that the replacement faucet will fit. To make this task easier, you can use two wrenches: one to hold the fixture, and the other to turn the nut on the water supply line. When you’re finished, turn on the hot and cold water supply and check for leaks.
After disconnecting the supply lines, you’ll need to remove the old bathtub faucet’s handle and replace it with the new one. Before doing this, make sure to shut off the water supply and drain the water. Using a socket wrench is an essential part of replacing a bathtub faucet. You can buy one at a hardware store and it’s made specifically for removing valves and pipes. Make sure you use it properly so you don’t cause any further problems.
Remove screws
If your bathtub faucet isn’t working, you may have to remove all handles before you can work on the repair. To do this, first remove the screw securing the faucet handle. You can usually remove this screw with a socket wrench found at a hardware store. These wrenches are specifically made to remove screws from valves and pipes. Next, remove the handle. Using the same method, you can replace the stem and handle.
To remove the faucet, you must first unscrew one or more screws from the existing unit. You can also place a drop cloth or towel in the bottom of the tub to prevent small pieces from falling into the drain. This step may take up to 6 hours. Once you’ve finished removing the screws, you can replace the faucet with new parts. To ensure the safety of your children, you may want to keep a drop cloth in the bottom of the tub.
Once you’ve removed the screws, you can remove the spout from the base. Be careful not to break the pipes as this could lead to a nasty surprise bath. You should also be careful when removing the handles. Be sure to turn off the water before you take a plunge to avoid splashing water all over the floor. Once you’re out of the bathtub, use a putty knife to remove them.
When removing the handles, make sure to carefully unscrew the set screws on both sides of the faucet. These screws are often found on the underside of the spout, close to the wall. You may have trouble finding the set screws, so you might want to use a flashlight to find them. To remove these screws, you will need a hex/Allen wrench or a small Phillips head screwdriver.
Remove escutcheon plate
To replace a bathtub faucet, you must first remove the escutcheon plate from the wall. Typically, this plate is secured with screws or caulk. Sometimes, it is also held in place by the plumbing fixture. To remove it, locate the screws and unscrew them. Then, remove the caulk and wiggle the plate to make sure it is loose. Then, follow the steps below to install a new faucet.
First, remove the escutcheon plate from the bathtub faucet. The plate covers the gap between the pipe and the wall. In addition, it may cover unused holes in the countertop for a soap dispenser, air gaps, or spray heads. Escutcheon plates are decorative pieces that complete the look of your plumbing fixtures. To perform the repair, remove the escutcheon plate. This part is attached to the water supply pipe.
To remove the escutcheon plate, first unscrew the two screws holding it to the wall. Next, pull the plate away from the wall. Now, you’ll have access to the cartridge. Make sure you use new O-rings for the cartridge to prevent leaks. Finally, replace the escutcheon plate with the new one. To replace the cartridge, repeat the previous step.
If the escutcheon plate is damaged, the screws holding it on are often very tight. To avoid having to deal with these screws, you can buy a replacement kit to fix this problem. To dismantle the faucet, you can also take out the tub spout. The spout can also be replaced. Just be sure to cover the drain with a sheet or towel before you begin disassembling it.
Remove handle
To replace a bathtub faucet, you’ll need to take the old one out first. To do this, you can use a flathead screwdriver to pry off the plastic cover and the index insert. Then, using a Phillips or flathead screwdriver, remove the handle screw. In some cases, a faucet handle puller may be needed. Once the handle has been removed, you can replace it with a new one.
To replace a bathtub faucet, you will first need to measure the existing fixtures. This will help you determine which parts you need. Alternatively, you can ask a store associate for help to ensure you get the right parts. Make sure you measure the pipe length, as you might not have the right length. Also, make sure the new faucet fits in the new pipe. Don’t overtighten the new spout, as it could damage the pipe.
Depending on the type of tub faucet, you’ll have to remove the escutcheon plate. The plate is behind the handle and may have two Phillips-head screws. The outer edge may have a small Allen head set screw as well. If you don’t have any screws, you’ll need to use an Allen wrench to unscrew it. Then, unscrew the securing screw and pull the handle away from the wall.
A special handle puller is useful for difficult handles. This tool has a screwhead that you can unscrew with a flathead or Phillips screwdriver. Once you’ve removed the screw, you can remove the handle, the stem assembly, and the escutcheon plate. If the faucet has a cartridge, you’ll need to remove it as well. You can also use a special bath socket wrench, which looks similar to a spark plug wrench.
Remove spout adapter
Identify the type of spout adapter you need. For example, a slip-on spout does not have a set screw. Instead, it fits onto a pipe without threads. If you’re not sure which type you need, you can look at the manual to find out how to install it. Afterward, you can remove the spout adapter.
To remove the spout adapter, you must first turn off the water supply to the tub. Then, close the faucet’s handle by unscrewing the corresponding screw. If the old spout is attached to a copper threaded fitting, you need to use WD-40 to loosen it. To do this, insert an extension straw with WD-40 and place it into the fixture. Leave it for about ten minutes to do its job. Now, you can use an Allen wrench or pliers to twist the spout. Be sure to use steady pressure to encourage movement.
Next, remove the spout adapter from the wall. Turn the tub spout counterclockwise and then pull it out of the wall. Be careful not to cut the pipe. It may crack or splinter. If you’ve been using a soldered brass adapter, make sure you’re aware of the risks and safety precautions when working with this type of faucet adapter.
After loosening the set screw, turn the spout counterclockwise to loosen it. Ensure that you use plumber’s tape. Other types of tape can cause damage to pipes. Then, install the new spout adapter. You can then tighten the new spout adapter by hand. If the spout adapter is loose, it is time to replace the bathtub faucet.
