We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.
When you’re dealing with a stubborn clog in your toilet, you need to know how to plunge toilet and how to use a drain snake. To use a plunger, you should first make sure the water level is high enough in the bowl. If this step is not successful, you can use a drain snake or toilet auger to help you solve the problem. Then, just submerge the plunger cup’s head in water.
Dissolving a clog with a plunger
If your toilet is clogged, it’s a frustrating and messy job. While a plunger will often solve the problem, you might also need to resort to other methods. You can always bring gloves with you when unclogging a toilet to prevent any injuries or damage to the toilet. Listed below are some methods to try if a plunger isn’t working.
Toilet plungers are the simplest way to unclog a toilet. The plunger is designed to be pushed against the toilet outlet hole to apply high-pressure to clear the clog. The high-pressure action of the plunger will dissolve most toilet paper clogs, allowing water to flow freely through the sewer line. When using a toilet plunger, make sure to hold the plunger firmly against the outlet hole so that the plunger has a tight seal.
After you’ve used a toilet plunger, you’ll need to empty the bowl to see if it completely dissolves the clog. When you’re done, flush the toilet to check that it dissolved the toilet paper. If the paper is too stubborn to dissolve, you might need to try an auger. A toilet auger works well for this task. However, you should always be careful not to use excessive force to push the plunger, as you may cause the plunger to become clogged again.
When a plunger isn’t enough to clear a clog, you can also try using hot water and a bit of dish soap to break up the clog. This method is best suited for minor clogs, as the hot water can help melt away the clog. If the clog is severe, you may need to manually remove it. In addition to using a plunger, you can also try placing a plastic bottle filled with warm water inside the toilet drain opening. This will create pressure and force the waste to move through the pipes.
Another effective way to dissolve a clog is to use household bleach. The process is similar to using dish soap, but you’ll need to use two or three cups of household bleach instead. Be sure to let the mixture sit for 10 minutes before flushing. It should dissolve the clog and leave the bowl clean. Soap is a common household item and is easy to find.
Using a drain snake
If you’ve tried using a plunger to clear your clogged drain, you probably know how difficult it can be. Before you try using a drain snake, make sure you follow these tips. First, be sure to put on protective gear, including rubber gloves and safety goggles. Once you have the proper gear on, insert the snake into the drain opening. Crank the drum handle clockwise until the auger starts moving down the drain. Continue to feed the snake until it feels resistance and, ideally, a clog is present.
Once you’ve unclogged the drain, try using a drain snake or a plumber’s snake. This equipment is 30 feet long and is designed to turn a slow-moving drain. It’s best to use a snake with a longer length and not jam it too tightly into the pipe. Alternatively, you can use a shorter snake to turn the drain. In either case, it’s important to use a drain snake that is designed for toilet use.
If you’re not sure whether you can handle the snake, you can also rent one from a local hardware store. These augers can be used to clear clogs from toilets, sinks, and showers. However, before using one of these tools, be sure to follow the instructions provided by the dealer. Simply insert the snake end into the opening, and it will travel down the drain. It can require some pressure to bend around the trap, but it will eventually slide through the clog.
When using a drain snake to plunge toilet, make sure you have water in the tank before you insert the cable into the drain. Then, reposition the snake counterclockwise to break the clog and pull it out. Once the clog has been removed, the water level should return to normal. To use a drain snake, be sure to clean the snake properly after use. The plunger itself is not a permanent fix, and may cause damage to the pipes.
Once you’ve removed the clog, it’s time to try the next method. You can use a drain snake to remove stubborn clogs that can’t be removed by a traditional plunger. It’s made of corkscrew-tipped wire that can drill through clogs and clean the drain. Unlike a plunger, however, a drain snake does not damage the surface of the toilet.
Using a toilet auger
Using a toilet auger to plunge your toilet is a great way to remove clogs from your sink or bathtub drain. It’s effective in clearing a clog by breaking up the blockage and letting you flush again. Once the clog has been removed, you should rinse the auger under hot water to remove the remaining debris. If possible, use toilet paper. Do not flush sanitary products, dental floss, or hair down the toilet. Older pipes may require lighter ply toilet paper.
To use a toilet auger, attach a cable to the handle and crank it backwards until it reaches full extension. A clog may be large enough to prevent the auger from being used. When the cable is fully extended, pull it backward to free the auger head. If the clog is large enough, the auger handle can be rotated a few times.
An auger is a good choice if you can’t reach the toilet drain through a traditional method. Its long cable goes through the drain, protecting the toilet bowl from scratches. While a standard drain snake can scratch the porcelain in the bowl, an auger will not. By utilizing an auger, you can easily plunge a toilet and save yourself a ton of time and money.
The auger’s rotating handle helps it snake deeper into the toilet. Once the auger reaches the clog, it will break it up and pull it out. If you don’t have an auger, you can try using a plunger to unclog the toilet. If the auger doesn’t work, you may have to push a plumber’s snake through the blockage. In most cases, however, a plunger will clear the clog and unclog your toilet.
Using a toilet auger is a great way to solve a clog in a bathroom drain without calling a plumber. The auger comes with safety instructions and can be rented for as low as $10 per day. Once it’s inserted into the drain, the auger cable will turn in a clockwise direction. Once you’re done, you’ll need to pull the auger cable back into the drum.
Submerging the head of the plunger in water
To plunge a toilet, you must first put enough water in the toilet bowl to cover the plunger’s head. Hold the plunger with both hands, and immerse it in water until you feel a strong suction. You must make sure that the water completely covers the head of the plunger, and that the water does not spill out into the bowl. Make sure that the water level in the toilet bowl is at least halfway full before plunging. If there is too much water, empty it with a bucket.
If you do not have enough water to submerge the head of the plunger, you will not be able to get a good suction, and you will end up wasting your time. Ensure that you have enough water before you start this process and stop periodically to add more water. If the water level drops below the head, you will have to add more water. However, you can use a lubricant to make the plunger work better. You can use coconut or vegetable shortening to lubricate the plunger head.
A flange-style plunger offers optimal suction. When using a flange-style plunger, make sure the rubber ring of the plunger is inserted into the toilet opening. Then, take a firm but gentle plunge for about 20 seconds. Be careful not to push or pull too hard as it may break the seal. In case of a larger clog, a plumber should be consulted to diagnose it.
If the clog is visible, you should attempt to remove it with your hands before plunging the toilet. If you cannot remove the clog using these methods, you may have to resort to a different method. For best results, you should try to flush the toilet with some bleach and washing liquid, then plunge again. That should do the trick. Finally, you must clean the head of the plunger so it can work effectively on stubborn clogs.
A standard plunger can also be used to unclog a bathtub drain. Insert the plunger at a 45 or 90-degree angle and push down a few times until you clear the clog. Repeat the process for about 20 seconds. A gurgling sound may indicate that the clog is clear. If the sound does not occur after the first attempt, then it may be due to an old plunger or a weak seal.
