How to Make Sliding Cabinet Doors

We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.

Are you thinking about making your own sliding cabinet doors? If so, you’ve come to the right place! This project is easy, cheap, and quick! Let’s get started! Measure the opening for your cabinet doors with a tape measure. Also, measure the thickness of the sliding door to determine the length of the track. Set your router bit to 1/8 inch wider than the door thickness. Cut a board of 1-by-2-by-96 inches and mark the length with pencil.

Easy

One of the best ways to add a decorative touch to your kitchen is to make sliding cabinet doors. These cabinet doors are typically made of plywood, and they do not require any molding or shaping. Most sliding cabinet doors are made from matching hardwood plywood. The thickness of the plywood should be 3/8″ to 1/2″. Depending on the design, you may need a thinner plywood if you plan to use metal tracks. After you’ve made the wooden panels, you can apply a wood finish.

When you purchase commercially manufactured sliding cabinetry, you’ll find that these doors slide out of the bottom or upper track. You’ll then need track hardware to remove them. You can buy these sliding cabinet door hardware kits from a cabinet door manufacturer online, but it’s usually cheaper to cut them yourself. Make sure to check the dimensions of the sliding cabinet doors before purchasing them. After you’ve measured the dimensions, mark them with a straight edge to ensure a proper fit. Then, cut the door just short of the line. It will be easier to sand the door once it’s cut.

To begin, lay the plywood panel on a table. Place the panel with the good side facing up and saw the tenons. You can then use a miter gauge to keep the wood steady while you cut the tenons. When you’ve cut the panel to size, you’ll need to affix it to the rails with the help of two screws. Once you’ve secured the door on the rails, you can then paint it and add decorative handles.

Cheap

Unlike hinged doors, sliding cabinet door panels are flat panels of wood. Sliding cabinet doors are typically constructed from 3/4″ hardwood plywood. If you plan to paint the cabinet, you may consider sanded softwood plywood instead of hardwood. This can also be a good alternative if you do not want to purchase expensive materials. Once you have purchased the sliding cabinet door panels, you can begin construction. You may need to order additional hardware for the sliding cabinet doors.

Sliding cabinet doors are generally more expensive than hinged doors, but they do come with some advantages. First, they have a broader opening than hinged doors. Then, the bottom groove is wider than the top. This design is more convenient as it does not bind and prevents debris from accumulating. The sliding action is improved by lubrication. Because most Americans are lazy and forget to do the work, this kind of hardware usually comes with a ten-year guarantee.

Simple

You can make sliding cabinet doors by following a couple of steps. First, you will need to make sure that the track is level with the edge of the cabinet door. The track must be approximately 1/2 inch from the lip of the top of the door. Once the track is level, you can install the doors. After installation, make sure that you apply paste wax to the track to make it slide smoothly. After a week, you should have finished your cabinet door.

Read More:   How to Quarter Saw a Log

Next, you need to cut a sheet of plywood to fit the opening of the cabinet. Cut a 3/4-inch board to the required length and width. You’ll need to cut the door slightly longer than the width. Then, use a router bit that is 1/8 inch wider than the thickness of the door. You’ll also need to cut the door just short of the line. This way, you’ll have room for sanding without removing too much wood.

Next, prepare the cabinet pieces. Miter cuts can be made by using a router and a bit for interlocking plywood corners. Once you’ve completed all the cuts, you’re ready to use the sander. Apply glue to the mating surfaces. Next, fold up the sides of the cabinet. Use a pneumatic brad nailer to nailed the two halves together. If you don’t have the tools to sand the door, use a stain instead.

Cost

Sliding cabinet doors are easier to build and tend to be more expensive than hinged doors. Unlike hinged doors, sliding cabinet doors require no face frame around the opening of the cabinet. The sliding track is cut into the part of the cabinet, and may affect the appearance of the cabinet itself. If you want to avoid the cost of metal tracks, opt for 3/4-inch hardwood plywood instead. If you want to avoid this extra expense, you can buy cabinets that are painted.

Sliding cabinet doors are also available in glass. They are normally assembled by a glass store and include the top and bottom trim pieces, a track system, and a handle and ground indentation. Wood-framed sliding doors are also available. Wood strips would be routed on the back to create an inset. The wood frame is then fitted with the glass panels. A sliding door can cost anywhere from $500 to $1,200.

Some models include a screen. Pre-hung models typically have one. Retractable screens cost between $100 and $400 and retract into the side channel when not in use. These features allow you to see what’s outside without removing the screens. They may also be easier to install if you have some knowledge of how to assemble cabinets. You can hire a contractor or handyman to install the doors if you don’t feel confident doing the job yourself.

Dimensions

Sliding cabinet doors do not require molding and shaping like hinged cabinet doors do. They are made from a flat panel of plywood, typically 3/8″ to 1/2″ thick. Wood cabinet doors are also available in matching colors. The plywood thickness is usually 3/4″ to 1/2″, but they may need a little more if the sliding cabinet door has metal tracks. Listed below are the dimensions of sliding cabinet doors. They can vary from cabinet to cabinet, so the exact measurements should be noted.

Double-motion sliding cabinet door hardware is a popular choice for deep and large cabinets. Unlike hinged cabinet doors, these units slide smoothly and do not require a lot of energy. They also slide smoothly when in use. They are also great for use in bathroom and kitchen pantries. The dimensions of sliding cabinet doors vary, so make sure to take this into consideration when shopping for your new sliding cabinets. You can also check with the manufacturer if they offer free-standing doors, but this is not a requirement.

The dimensions of sliding cabinet doors are slightly different than hinged doors. When choosing a width, be sure to leave enough room in the middle of the door. Too much overlap will result in a smaller opening when the door is open. The height of sliding cabinet doors is also important, as the door must be at the right height to go into the track. Once the proper width has been calculated, you can begin the process of measuring your cabinets.

Read More:   How to Make a Flip Down Keyboard Drawer

Installation

Sliding cabinet doors are easy to install and do not require molding or shaping. They are simply flat panels of plywood. Typically, you will use a matching hardwood plywood for the cabinet doors. The doors will require a 3/8″ to 1/2″ thick plywood, but you may need a 1/4″ thicker panel for those with metal tracks. The installation process is similar to installing hinged cabinet doors. To install the sliding cabinet door, follow these instructions.

To install the track, measure the length of the cabinet opening. The track must be placed above the opening. Be sure to allow enough room above the door opening to accommodate the track. Once you’ve determined the length of the track, assemble the cabinet by attaching the sides and bottom. If the doors don’t fit, block them so that they don’t fall over. This is a simple installation procedure, but it is important that you have the right hardware kit before you begin.

If you’re installing sliding cabinet doors, you should pre-drill holes in the top and bottom rails and use screws to secure the track in place. After that, install the doors. Make sure the door is level. The upper track should have a 1/8″ gap between the two sides. Install the rollers in the tracks by pre-drilling the holes in the bottom and the top edges. If you’re using a pre-drilled hole, use the largest metal washers that you can find.

Why trust Handyman.Guide?

s written by Itamar Ben-Dor, who has 25 years of experience in renovations, carpentry, locks, creation, landscaping, painting, furniture construction, and furniture renovation, works with concrete, plumbing, door repair, and more.

Itamar Ben-Dor has been in the home improvement business for over 25 years. Itamar Ben-Dor is a jack of all trades. He's worked in the renovation field for years, doing everything from locksmithing to carpentry. He's a small repairs specialist. But his true passion lies in furniture construction and renovation - he loves seeing old pieces come back to life with some new woodwork or a fresh coat of paint.

He has taken courses on many topics in these fields at professional colleges in Israel. Over the years, Itamar has also become quite skilled in gardening, carpentry, and renovations. He's worked on projects of all sizes, from massive renovations to small repairs. No job is too big or too small for him!


Disclosure: handyman.guide participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to Amazon.com and affiliated sites.

handymanguidewebsite@gmail.com
HandyMan.Guide
Logo