How to Use a Table Saw Taper Jig

We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.

A table saw taper jig makes it easy to cut an angled rip. It can also be used to straighten a live edge or cut awkwardly shaped boards. It works by slipping over the live edge. It is very easy to build and can be purchased at most home improvement stores. The following steps will help you make the most of your newest tool. Continue reading to learn how to use a table saw taper jig.

Before using the taper jig, set the blade to a depth of about 1/4 in. Then, place the sled in the jig. You should then hold it flush with the teeth of the blade. Next, place the support block and stop block against the fence. Once you’ve secured the support block, screw them to the base of the sled. This will prevent the sled from sliding off the jig during the cut.

Once you’ve established the position of the jig, you need to attach the leg to the base. Then, tighten it to ensure the piece doesn’t shift during cutting. Don’t forget to secure the safety handle on the sled if you are cutting taper-shaped pieces. Then, attach the leg to the sled, and adjust the angle accordingly. The angle jig will keep the sled in place while you work.

You need to mount the jig on the table saw by setting it up properly. The rip fence should be aligned with the rip fence. Then, use the jig to feed the cut. The jig should remain on the cut surface for a while before you remove the support and clamp the legs to the table. During the cut, you should always keep your hands behind the jig’s support.

Once the jig is in position, you should set the blade in the appropriate position. The runner should be set on the table saw by the leg and should be placed in the t-slot. The runner and baseplate should be properly aligned before assembling the jig. The runner should be set against the rip fence by a horizontal plane. It should be flush with the rip fence so that it will not interfere with the rip.

Once the jig is attached to the table saw, attach a 2-inch-wide piece of wood to the base using deck screws. The leg should be flat or butted against the left edge to push the board through the blade. The jig should be screwed into the table saw with hold-downs. It is then necessary to attach a spreader bracket to the legs of the table saw.

Afterwards, set the jig in place. Ensure that the leg is flush with the teeth of the blade. Then, insert the jig through the saw blade. The blade will follow the jig along the fence. The legs should be spaced apart by four inches. The jig should be positioned in a way that it prevents the blade from rotating.

After affixing the leg to the jig, set the blade so that it’s about 1/8-inch above the rip fence. Then, place the leg against the fence and align it with the ripped edge of the plywood. Once it’s flush with the edge, the jig is ready to be used. The jig can be adjusted easily to fit any table saw.

A table saw taper jig is a great tool to use when cutting angles on the top or sides of a table. It is easy to use, safe, and will save you a lot of time and effort. Besides, it will make it easier for you to make cuts at an angle. The instructions will help you create the jig. When you have a scrap of wood, use it for the support block.

Read More:   How to Make a Tack Cloth

After building the taper jig, you should install the clamps. You can use a jig to make a notch in a plywood. However, the taper jug will not be as effective as a table saw fence. It should be mounted to the table saw fence and secured with a piece of hardware. After affixing the taper joist, screw it into the plywood and start cutting.

Why trust Handyman.Guide?

s written by Itamar Ben-Dor, who has 25 years of experience in renovations, carpentry, locks, creation, landscaping, painting, furniture construction, and furniture renovation, works with concrete, plumbing, door repair, and more.

Itamar Ben-Dor has been in the home improvement business for over 25 years. Itamar Ben-Dor is a jack of all trades. He's worked in the renovation field for years, doing everything from locksmithing to carpentry. He's a small repairs specialist. But his true passion lies in furniture construction and renovation - he loves seeing old pieces come back to life with some new woodwork or a fresh coat of paint.

He has taken courses on many topics in these fields at professional colleges in Israel. Over the years, Itamar has also become quite skilled in gardening, carpentry, and renovations. He's worked on projects of all sizes, from massive renovations to small repairs. No job is too big or too small for him!


Disclosure: handyman.guide participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to Amazon.com and affiliated sites.

HandyMan.Guide
Logo