How to Sand Round Objects

We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.

If you’ve ever sanded something round, you know how hard it is to find scratches. Even after a thorough examination, the scratches may still be difficult to spot. This is where glancing light comes in handy. You can place the light at a level that’s about the same as your chest and point it towards the sanding bench. This will help you determine whether any scratches are present and where to focus your efforts.

Using a multi-sander

Many furniture makers use an assortment of electric sanders. Which one is best depends on the purpose and application. If you’re making cabinets, for example, your project will involve many interlocking and built-in components, so you’ll likely use a belt sander or a sheet finishing sander. However, if you’re sanding round objects, you may want to consider a different type of sander.

A delta sander is best for small, intricate areas. The triangular sanding plate makes it ideal for smaller surfaces. Its weight and ergonomics make it easy to balance while working. There’s no risk of slipping while you’re sanding. The sander’s adjustable speed allows you to work efficiently with different types of sandpaper.

Another type of sander is called an orbital sander. It has two distinct types of blades: a wide sanding pad for coarse sanding, and a narrow sanding pad for finer detail work. This sander is useful for small details and reaches areas that orbital sanders can’t reach. Another benefit is its portability.

While a sanding block may be easier to use on round surfaces, a sanding sponge is ideal for curved surfaces. A sponge can follow the contours of the object, making it easier to sand crown-shaped projects. When using a multi-sander, make sure you’re holding the correct angle when sanding. You can then apply duct tape to the back of the sandpaper to reinforce it while you’re sanding.

While a multi-sander can sand round objects, it should be used carefully. Always wear eye and hearing protection. It will help keep the surface clean and prevent you from getting frustrated by clinging wood dust. It is also important to keep the sander level when you’re sanding wood, as angling it will damage the sandpaper and cause it to warp and fall apart.

Using a sanding block

Making your own sanding block is easy if you have a piece of medium-density fiberboard lying around. You can cut it into two-1/2 x 5-inch blocks and spray-adhere sandpaper to the block’s back and sides. Next, assemble your sanding block and sand the desired object. To create a chamfer, sand the object to a finish of 120-grit sandpaper.

The sandpaper strip should be tightly wrapped and smooth. Place the sandpaper strip on top of the sanding block and make sure it is secure. Now, use your hand to rest the curved top of the block on the surface and gently press down on it. It is easy to sand round objects, especially corners. Using a sanding block is a more economical option than a power sander.

You can also use sandpaper to sand flat objects. You can get three pieces of sandpaper from a standard sheet of sandpaper. To save time, you can even buy a pre-cut sheet of sand paper and make your own sandpaper. But, it is best to purchase a sanding block that can conform to the shape of the object you are sanding.

Read More:   Advantages of an Electronic Tape Measure

Using a sanding block is more effective than using a hand-held sander. It is easier to use, and it provides a more accurate result. And, you can even jig it up if you want to improve efficiency and accuracy. The circular motion prevents rocking work and unwanted curvatures. When you make a circular motion with the sandpaper, you’ll achieve a perfect finish.

Using a Dremel multi-vise

Using a Dremel Multi-Vise allows you to clamp a project to your workbench, table, or countertop and can be tilted 50 degrees. This tool holds your project securely for grinding, drilling, or other finishing tasks. Not only is it ideal for refinishing wood and metal, but it can also be used to recycle aluminum cans. While the base unit is designed to clamp an object to a workbench, the Dremel Multi-Vise can also serve as a stand-alone bar clamp.

To use a Dremel Multi-Vise, you must first have the appropriate sandpaper bits. When using a multi-vise, you should set the speed between two and ten. A low speed is appropriate for wood, metal, or plastic. Then, hold the object firmly while you run the sandpaper bit across it. Be sure to check the sandpaper bit before you begin sanding it because a dull sandpaper can leave marks on your object. Always have spare sandpaper bits available.

Before you begin sanding round objects, make sure to use a safety mask and eye protection. A Dremel can be a loud tool, so make sure to wear eye protection and earplugs. Another thing to remember when using a Dremel is to wear safety glasses. You never know when a stone may chip unexpectedly. ANSI-rated safety glasses are required.

When using a Dremel multi-vise, always make sure you have the correct bit for the job. A flat disk sanding bit is perfect for grinding metal and is much easier to use than a drill. A flat disk shape bit is best for round grinds. The Dremel comes with four different collet sizes. Once you have found the correct size, insert the bit into the collet. When done, tighten the collet nut and switch to the appropriate speed.

Changing grits

One of the most important tips to remember when sanding a round object is to change the grits as you progress. You will have to change the grit when you reach a point where you are unable to make any improvement with the grit you are using. Changing grits will help you continue the process and smooth out the surface. It is important to pay close attention to the surface as you sand.

First of all, you must determine the type of wood you’re sanding. Generally, hardwoods need a coarser grit than softwoods. If you’re sanding a pallet, you’ll want to use a coarser grit for this task. The same applies to sanding a round object. Depending on the surface, you’ll need a coarser grit to remove more material, and a finer grit to smooth the object.

While coarse grits are ideal for removing large surface imperfections, it’s best to use medium grits to remove medium-sized surface flaws. For finishing touches, a fine grit of about 180 or 200 is great. Remember to keep your sandpaper free of debris as it could get in the way of the smoothing process. If the surface is metal, you may need higher grits.

You can also change the grits when sanding a round object. You can start with a coarser grit and work your way down to a finer one. Once you have achieved the desired level, move on to the next grit until you’re completely satisfied with the final result. If you’re unsure of whether or not a certain grit is right for a particular object, check the manufacturers’ instructions.

Read More:   How to Stain Alder Wood

Avoiding flat spots

There are several ways to avoid flat spots when sanding round objects. The first way is to look at the surface of the round object and identify its ridges and hills. For this, you can either use a spotlight or run a straight edge across it in different directions and mark high and low areas with pencil. Next, you can sand the board evenly across the ridges and hills, but be careful not to leave any valleys unmarked. A simple solution to this problem is to apply duct tape to the back of the object, as this will help reinforce the sandpaper.

Sanding a round object may seem daunting, but it doesn’t have to be. Using quality abrasives can speed up the process and make it flow much more smoothly. Although it’s tedious to sand round objects, the end results are worth it. If you want to avoid common mistakes, here are some tips and tricks you should follow:

Why trust Handyman.Guide?

s written by Itamar Ben-Dor, who has 25 years of experience in renovations, carpentry, locks, creation, landscaping, painting, furniture construction, and furniture renovation, works with concrete, plumbing, door repair, and more.

Itamar Ben-Dor has been in the home improvement business for over 25 years. Itamar Ben-Dor is a jack of all trades. He's worked in the renovation field for years, doing everything from locksmithing to carpentry. He's a small repairs specialist. But his true passion lies in furniture construction and renovation - he loves seeing old pieces come back to life with some new woodwork or a fresh coat of paint.

He has taken courses on many topics in these fields at professional colleges in Israel. Over the years, Itamar has also become quite skilled in gardening, carpentry, and renovations. He's worked on projects of all sizes, from massive renovations to small repairs. No job is too big or too small for him!


Disclosure: handyman.guide participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to Amazon.com and affiliated sites.

HandyMan.Guide
Logo