We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.
The screw that holds the drill chuck onto the workbench is left-handed. To remove the drill chuck, unscrew the screw and clamp a sturdy allen key to the chuck. Holding the drill body in a vice, you can whack the chuck off. Alternatively, you can use large pipe grips to hold the drill body. Depending on the size of the drill, you may need to adjust the vice to fit the drill’s size.
Tap hex key in counter-clockwise direction
There are two ways to remove a drill chuck. Using a hex key with a length of about 1/4″ (6.4mm) or larger can loosen it, or you can use a screwdriver to remove it. You must make sure that the screwdriver is in the correct direction or the chuck will not come out. Use the larger of the two methods, whichever works better for you.
Before removing the drill chuck, turn the drill off. If the drill chuck is spinning too fast, replace the drill bit. Then, remove the drill’s battery pack and turn off the Rotation Direction Sensor (RDS). Once you have turned off the drill, open the jaws of the chuck. Remove the bit from the chuck, and tap the hex key in a counter-clockwise direction to tighten it.
Next, remove the drill chuck. To do this, you must loosen the jaws of the chuck and then thread it onto the spindle. You can do this with a hex key of 5/16″ and a mallet. Tap the key in a counter-clockwise direction to loosen it further. If you cannot find an allen key that is the right size, you can use a large Allen key and screw it in counter-clockwise direction to remove the chuck.
Before attempting to remove a drill chuck, you must remove the Allen wrench from the chuck. The Allen wrench is the most common tool to loosen a drill chuck. Use a wrench of the right size and ensure that the key overhangs the workbench. Hold the wrench horizontally over the drill. Give it a sharp downward strike with a mallet. Continue to do this until the chuck is loose enough to be removed.
Next, remove the drill bit. A drill bit may become stuck in the drill chuck because the jaws are not aligned properly. If this happens, you need to remove the drill bit from the chuck. Then, you can remove the chuck by rotating it in a counter-clockwise direction. After this, you can easily install a new bit with a different number on it.
You can also use a Phillips head screwdriver to loosen the retaining screw in the chuck. Alternatively, you can use a wrench to remove the keyless chuck from the drill. You can also use a keyless hex key to replace it. There are different methods to replace a drill chuck, but the procedure is the same.
Insert wedge between chuck back and cross pin
To repair a damaged part, you may need to insert a wedge between the drill chuck back and the cross pin. Wedges are inexpensive and useful for a variety of projects. Just make sure you have the right size for your tool. You can purchase them from a hardware store. To prevent further damage, use them only if they are the right size. In the case of a chuck that does not provide a shoulder, insert a wedge between the back of the drill chuck and the cross pin.
If you use a keyless drill chuck, you may have a problem with the threads. In such a case, it will be difficult for you to open and close the drill chuck. Luckily, there is a simple solution. You can use a wedge-shaped jig to wedge between the cross pin and the back of the drill chuck. When the wedge is used correctly, the cross pin and the drill chuck will slide off without any problem.
Reattach drill chuck
To remove the reattachable drill chuck, you can use a medium-thick screwdriver. Make sure the wrench passes right and left of the center of the quill, and do not pass into it. Next, place a flashlight and mirror inside the chuck to see if the screw head is visible. If so, you must remove the screw. Be careful, as some chuck screws are left-handed.
After removing the chuck, you can use a 1/2-inch hex wrench to loosen it. Ensure that the drill is on a workbench or ledge. With the long end of the hex wrench, tap the drill chuck counterclockwise until it disengages. Next, unscrew the chuck using your hand. Once the chuck is free, clean the spindle head with a rag. It is also important to clean the threads before threading in a new chuck.
Changing or servicing the reattachable drill chuck is not difficult. Most chucks can be serviced by cleaning them while in place, but if you are using the drill regularly, you might want to replace it. Luckily, there are some tools on the market that make this process easy. You can buy a wedge-shaped jig for a reasonable price, which will make removing the chuck a breeze.
Another way to fix this problem is to remove the chuck from the spindle. If the chuck is too tight, you should turn the spindle in a clockwise direction, but do not lock it in a vice. This will prevent the chuck from becoming loose and may even damage the drill. When this happens, it is best to consult with a technician or a DEWALT Factory service center to fix it.
If your drill chuck is too rusty, the jaws may not open properly. Rusty chuck jaws can prevent the drill bit from spinning freely. Clean them with mineral spirits and compressed air. Do this repeatedly until the chuck is free of rust. If rust prevents the chuck from opening, you can force the jaws back inside the chuck with a mallet.
In some cases, a loose drill chuck may also prevent screws from turning straight. Before you can tighten the drill chuck, turn off the drill’s rotation direction sensor and unplug the battery pack. Next, you should remove the drill battery. You can then turn the drill off. Afterward, you should close the drill chuck completely and replace the drill bit. Once the drill bit is replaced, reattach it to the drill chuck.
After reattaching the drill chuck, make sure the bit fits properly into the holes of the chuck. If it does, use a safety glove or cloth to hold the drill bit while rotating the gear. Once it is loose, the chuck should be easy to remove. If it is a keyless chuck, you can fix it by following the same steps as for keyed chucks.
