How to Glue Two Pieces of Wood Together to Make a Thin Piece of Furniture

We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.

If you want to learn how to glue two pieces of wood together to create a thick piece, then read this article. You will learn how to prepare the pieces for gluing, how to apply wood glue, and how to clamp and time your work. This article will guide you through the process step by step. Follow these tips to achieve your goals. Then, you can build your project in no time at all.


Gluing two pieces of wood together is easy but there are certain things you should do before you begin. Make sure the pieces of wood are clean before you start the glue application. Remove all dust, wax, and old glue from the wood pieces. To clean the wood, use rubbing alcohol. This substance is flammable but will dry within five minutes. Clamp the pieces together while the glue dries.

For the best results, ensure that the wood is flat and clean before gluing. Avoid using end grains as these do not glue well. It is also important to choose a set of clamps with good quality. Do not overclamp as this could squeeze the glue out of the joint. Also, take care to use masking tape on the surfaces to be glued. Use “no-bleed” tape if using water-based finishes.

When gluing two pieces of wood together, try to think about the glue on a micro scale. When dry, the adhesive has tiny barbs and hooks. You can think of each hook or ridge as tiny barbs or hooks. If you think of it this way, you can see how this kind of glue works in a micro scale. And you can use it to make a thick piece of wood.

When it comes to plywood, you may need more thickness than the standard 3/4 inch. But since it is cheaper, 4/4 lumber is a better choice. This type of lumber is more stable than 8/4. This way, you can make a thick piece of wood without having to buy a thick board. However, when gluing two pieces of wood together to make a thick piece, always remember the basic principles of wood joining.


There are several steps involved in preparing two pieces of wood for glue application. You need to remove all contaminants from the surface and clean it thoroughly. You also need to roughen up the surface of the hooks to create more surfaces for the glue to adhere to. Another thing to consider is the temperature. Most glues sold in stores are water-based, and they are best used between 50 and 90 degrees Fahrenheit. Check the label to see what temperature is ideal for your particular glue.

Next, you must prepare both pieces of wood. First, you need to use the correct glue for the wood you are gluing. Make sure to buy a glue that is specifically designed for gluing wood. Gluing two pieces of wood together is simple, but you must be careful and use a good glue. The proper glue will ensure that your wood will stay put for a long time.

Once you’ve prepared the pieces of wood, you need to use a glue to adhere them together. If you’re using superglue, use a glue that has a tapered nozzle so that you can apply it more accurately. Apply about one drop per 6.5cm2 of wood. Wait 10 to 45 seconds for the glue to set, and then sand down the pieces flush.

Read More:   How to Round Wood Corners by Hand

First, prepare the surfaces of the two pieces of wood. Start by gluing the better side of the plywood to the worst side. Spread the glue generously between the two pieces of wood. You can use a stick or cauls to spread it evenly over the surface. Once it is glued, you can put the plywood on the glued side and secure it into place.


Before you begin gluing two pieces of wood together, make sure to check their diagonal measurements. If they’re off by 1/8 in., reposition the clamps to get them square again. If the clamps are off by 1/16 in., change the angle. A square frame will be easier to achieve with uneven pressure across the joints. If the two pieces are not square, the dimensional difference will increase as you tighten them.

If you want to avoid sliding wood while gluing, try using a rope clamp to hold the two pieces together. If you do not have clamps, consider using PVC pipes as an alternative. First, cut the pipe into quarter-inch pieces. Second, use a c-clamp improvised from PVC. Clamping the wood together is easy with PVC pipe.

If you don’t have wood clamps, you can make your own using scrap wood. Use a hammer and nail to secure the clamps. If you don’t want to buy clamps, you can also use masking tape. Remember to spread the glue evenly and press the pieces together. If you don’t have clamps, masking tape works well. Just make sure you have enough masking tape to cover both pieces of wood and wrap it tightly.

If you’re using wood for furniture construction, extra thickness is often desirable. It helps prevent warping. For a table, for example, extra thickness may make the piece look more sturdy and add a touch of elegance. It’s easy to glue two pieces together with clamps, as long as the wood is flat and clean. Make sure you use quality wood glue and clamps, as over-clamping will squeeze the glue out of the joint.


To build a thick piece of furniture, you’ll need to glue two pieces of plywood together. Plywood can only be a certain thickness, so you may need to glue two pieces together to meet your exact requirements. The glue will have to dry for 48 hours before it’s ready to be used. To speed up this process, use a fan to speed up the drying process.

Before you glue your two pieces of wood together, you’ll need to clean them. Remove all dust, wax, or old glue. You can use rubbing alcohol to wipe off any loose particles. Be careful, though, since rubbing alcohol is flammable and will evaporate in about 5 minutes. When applying the glue, make sure to leave some space between the two pieces of wood so that the glue has time to set and harden before you start gluing.

When applying the glue, be sure to use a good amount of it to ensure a consistent bead when clamping pressure. If you apply too little glue, you’ll have a clumpy mess and inconsistent bead. To avoid this, you’ll want to use a special wood glue made for wood. Wood glue is readily available in the market and will help you get your project done quickly.

Using superglue is another way to join thicker wood. It’s easier than using clamps and allows you to press the pieces together with a heavier object. This method is suitable for small wood pieces, but it will not be ideal for larger boards. When gluing two pieces of wood together, you can also use clamps. And you can wait 24 hours for the glue to fully dry.

Read More:   How to Use Gel Stain Using a Rag

Glue type

When you’re gluing two pieces of wood together to make a solid, thick piece of furniture, you’ll want to use a good wood glue, particularly if you’re going to be using a heavy object. Start by applying glue on one piece of wood, then place the other on the glued surface. Put a heavy object on the upper piece of wood, but make sure you spread it out evenly so the weight is equally distributed on the surface of the glued wood.

Depending on your project, you may use a different type of wood glue than you’d normally use. If you’re making a furniture table, epoxy glue is probably the best choice. Epoxy is a two-part glue, with a resin component and a hardening agent. When mixed, the glue sets into a strong and waterproof adhesive. It can adhere to a variety of materials, but is not ideal for tight-fitting joints.

For heavy-duty DIY projects, you’ll probably want to use a thicker wood glue. However, wood glues are often less effective at filling gaps because they soak into the wood, leaving very little structural integrity behind. That’s why most woodworkers use tight-fitting joints and small pieces of wood. Also, a wood glue requires clamping while it sets, which can result in gaps that don’t provide support.

You can also use an epoxy compound to fill gaps and join pieces together. While epoxy is more expensive and difficult to use, it provides a waterproof finish to your project. Take your time and read the instructions carefully to ensure the best results. You should choose a good adhesive if you want to use it outside. You can also use a clear glue to fix cracks in your furniture.

Why trust Handyman.Guide?

s written by Itamar Ben-Dor, who has 25 years of experience in renovations, carpentry, locks, creation, landscaping, painting, furniture construction, and furniture renovation, works with concrete, plumbing, door repair, and more.

Itamar Ben-Dor has been in the home improvement business for over 25 years. Itamar Ben-Dor is a jack of all trades. He's worked in the renovation field for years, doing everything from locksmithing to carpentry. He's a small repairs specialist. But his true passion lies in furniture construction and renovation - he loves seeing old pieces come back to life with some new woodwork or a fresh coat of paint.

He has taken courses on many topics in these fields at professional colleges in Israel. Over the years, Itamar has also become quite skilled in gardening, carpentry, and renovations. He's worked on projects of all sizes, from massive renovations to small repairs. No job is too big or too small for him!

Disclosure: participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to and affiliated sites.