How to Do a Sunburst Finish

We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.

If you’ve ever wanted to learn how to do a sunburst wood finish on your woodworking projects, you have come to the right place. Jeff Ross’ course on sunburst finishes demystifies the process and has 7.5 hours of high-quality video instructions. You’ll get to see hand-rubbed burst finishes, sprayed sunburst finishes, and even an FAQ page. All you have to do is purchase and register to access the course.

Creating a sunburst finish

Creating a sunburst finish is not difficult, but it does take a little bit of time and patience. A good course will help you to master this finishing technique. Jeff Jewitt of Homestead Finishing Products is the course instructor. The course includes 7.5 hours of high-quality video instructions. You will learn how to apply sunburst finishes with a spray gun or by hand. The course includes a FAQ page and a registration form.

To create a sunburst finish, you will need two nitro sprays. One for the edge and one for the center. You may have left over paint. This paint will darken the edges and make it easier to apply the sunburst. This step is also important if you plan to spray color onto a painted wooden surface. Once the body is painted, you can use the remaining paint on the neck.

A sunburst finish is generally applied on the face of a guitar. If the face of the guitar is natural, you should apply a thin layer of lacquer before applying the sunburst. Then, use a narrow putty knife to remove the old finish. You should hold the putty knife at a 45-degree angle to avoid scraping the wood. Next, wipe the entire body with the clear coat to soften the look and blend it.

Once you’ve applied the base stain, you can apply the shader stains and feather them with a cloth soaked in solvent. Remember, this process took a lot of time before the advent of spray equipment. Rattle cans were widely used for creating sunburst finishes in the days before spray equipment was available. Using nitro-based toners is a viable alternative to rattle cans. Using any of these methods, you can create a two-tone finish with minimal effort.

The sunburst guitar finish is one of the most challenging guitar finishes to create. It requires a lot of attention to detail. Gibson was the first to introduce the sunburst concept and has spawned several variations since then. Essentially, a sunburst finish is created by layering different shades of the finishing material on the surface of the guitar. The result is a sunburst effect that looks like a bright sun shining in the middle of the guitar’s surface. The finish is then furthered by adding darker colors around the center of the sunburst.

Creating a hand rubbbed burst finish

One of the most common questions from guitar customers is about how to create a Wrap finish. A technician at Sweetwater will start by evenly applying a dark color around the edges of the guitar top. Then, a worker in the Burst department will begin scraping the paint off by hand to reveal the natural maple underneath. This gives the guitar the appearance of being bound. When this process is complete, the guitar will have a beautiful, hand-rubbed burst finish.

Creating a spray-on burst finish

The Sunburst is a unique finish on guitars that adds a splash of color to the instrument. It is an extremely popular finish on acoustic and electric instruments, and is often referred to as the ‘flagship finish’ of the guitar industry. The spray-on method is extremely popular for many reasons, including its ease of use. There are many products on the market that are suitable for sunburst applications, including nitro based toners and guitar-specific toners.

Read More:   How to Dry Fresh Cut Lumber?

Before applying the sunburst finish, prepare the guitar by filling in the grain and applying four coats of sealer. For optimal results, lay the guitar flat on a small table or raised base, so that it can receive the finishing spray. Use paper to protect the base from overspray. Make sure to raise the body of the guitar a little off the base to avoid hard spray lines. Wood blocks can also be used as supports.

Why trust Handyman.Guide?

s written by Itamar Ben-Dor, who has 25 years of experience in renovations, carpentry, locks, creation, landscaping, painting, furniture construction, and furniture renovation, works with concrete, plumbing, door repair, and more.

Itamar Ben-Dor has been in the home improvement business for over 25 years. Itamar Ben-Dor is a jack of all trades. He's worked in the renovation field for years, doing everything from locksmithing to carpentry. He's a small repairs specialist. But his true passion lies in furniture construction and renovation - he loves seeing old pieces come back to life with some new woodwork or a fresh coat of paint.

He has taken courses on many topics in these fields at professional colleges in Israel. Over the years, Itamar has also become quite skilled in gardening, carpentry, and renovations. He's worked on projects of all sizes, from massive renovations to small repairs. No job is too big or too small for him!


Disclosure: handyman.guide participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to Amazon.com and affiliated sites.

HandyMan.Guide
Logo