We research in-depth and provide unbiased reviews and recommendations on the best products. We strive to give you the most accurate information. If you buy something through our links, we may earn a commission.
If you are installing a new handrail, you may be wondering how to attach one end to the wall. To help you with this project, we’ll discuss mounting the handrail to the wall, using plastic resin glue to bend a stair railing, and checking the level with a string level. This step is essential to ensuring that your railing is level. If the handrail isn’t seated on a stud, you will have to find a stud in the wall and mount it to that drywall.
Installing a handrail on a wall
If you’re installing a handrail on a wall, you’ll want to make sure to mount the handrail on a stud. To do this, simply drill two holes in the stud, and then insert a wood screw into each hole. Be sure to stagger the screws so that none of them hit the handrail in the process. Once the screws are in, you can screw the handrail end into place.
To begin installing the handrail, make reference marks on the studs, and at the intersection of the handrail and wall. These marks indicate the location of the support brackets. Then, install the brackets into place, ensuring that the bottom edge of the brackets is flush with the bottom edge of the handrail. Once the handrail is installed and secures, you are ready to mount it to the wall.
To start installing the handrail, mark the studs using a stud finder. Measure up from the bottom tread of the stairs and mark their location with 1-1/2 in. masking tape is useful for marking stud locations. Next, measure the handrail height. You’ll need to measure from the front edge of the first stair to the bottom tread of the second. This will determine the height of the handrail. Once you’ve made the measurements, cut the rail to match the marks. To finish, paint or stain the handrail.
After installing the handrail, you must install the handrail end on the wall. It is easy to install the end on the wall if you follow these instructions. The end of the handrail will be slightly longer than the rest of the handrail, but you can always trim the excess with a miter saw. Once the joint is completed, you’ll need to sand the edges. If you are using unfinished wooden handrail, you should paint it with a stain or polyurethane finish before installing the handrail end.
If you have brick or masonry in your home, you’ll probably need to use side-mount or surface-mount posts. Brick looks better with aluminum or powder-coated steel posts, but whichever you choose, they will all work with your railing system. You’ll also want to make sure to use posts that match your railing system, because some railing systems don’t work with different types of posts.
Using Weldwood’s plastic resin glue to bend a stair railing
If you’re in need of a bending rail for a stair, Weldwood’s plastic resin glue is your best option. This product comes in a small plastic jar that contains a soupy brown paste. Simply mix one half with water and apply it to the other half of the key. Allow it to dry for several hours.
Before you begin, make sure the glue is fresh and less than 6 months old. This is because plastic resin glue can get contaminated if it is too old. National Casein glue is a great choice if it is fresh. If it’s past that time, a second application of the glue should be done. Once the glue has dried, install the railing.
Checking for level
To ensure that your new handrail is level, use a string level to mark the location of studs on the wall where you’ll attach it. If you’re using a vinyl home, look for a visible nail on the vinyl facing the wall’s stud. Exterior electrical outlets also have studs next to the unit. If you don’t see any visible nails, use a stud finder or pencil to mark the wall.
When attaching a handrail end to a vertical post, make sure to check the wall for level and use 6″ timber screws to secure it to the wall. Using a miter saw, cut a 45 degree angle from the measured distance. This will ensure the handrail is level in all directions. If the handrail end is attached to a flat surface, use two people to do the job.
Before attaching the handrail end to the wall, take vertical measurements from the step nosings. You want to allow for nine inches of clearance, which is roughly equivalent to the height of an adult handrail. If you’re installing a handrail with multiple levels, you’ll want to check for level from the stair’s nose to the top of the wall. In most cases, the wall’s studs will match the steps, so you may have to take a few measurements.
Before assembling your handrail, you should set up a reference mark on each stud that meets the top of your first step. This mark will indicate the location of the support brackets. To attach the handrail end to wall, screw the bracket to the studs at the reference marks. Ensure that the bottom of the bracket is flush with the bottom edge of the handrail. Now, you’re ready to hang your handrail!
Using a string level
Before you begin, measure the length of your rail. Then, make vertical marks over the studs and space brackets evenly apart. If necessary, place additional brackets 2 3/4 inches below the marks. Using a torpedo level will help you keep your vertical lines plumb and your holes centered. You should also use it to line up brackets at the top and bottom.
Next, you need to make sure your handrail is level. You can use a string level to check for any errors, and to mark where your handrail is level with the wall. It is also helpful to use a spirit level to check the level of newel posts. The string level should align with the handrail, and the marks should be the same at the top, middle, and bottom of the handrail.
Before you start attaching the handrail, you must mark the stair’s walls. The distance between the handrail and the wall should be at least six inches. If the railing is wider than the stair, then it is too wide. If the stair has multiple levels, then the handrail should be at least one inch higher than the stair treads. You should also measure the handrail’s projection from the wall, or PW, or distance from the wall.
Using a string level to attach hand rail end to wall becomes very easy when you use a stud finder. You can even use a pencil or chalk to mark the studs before you attach the handrail end to the wall. After you have determined the height of the handrail, you can then attach it to the wall using the mounting brackets. Once you have attached the handrail end to the wall, you can then use the string level to attach the remaining portion of the handrail to the wall.
